How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
Right here in the next paragraph you can discover a good deal of reliable help and advice when it comes to Tools You Need to Install a New Bathtub .
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily available, the project can move easily; if you need to open up a wall to remove the old tub and place the new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub as well as set in the brand-new one. Make certain you have actually certified yourself for the job and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This post will assist you install a brand-new bathtub in your bathroom if you have currently gotten a brand-new bathtub as well as do not require to transform the plan of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Safeguard the faucet in position with the supplier given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind must be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bath tub in the required position. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the tub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the supply of water and examine all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally examine the overflow outlet and also the typical electrical outlet for leaks.
Lastly, repair the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been utilized a minimum of once as this will certainly resolve it into its last position.
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, resulting in issues with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can split rather early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very eager about Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the entire page. Are you aware of another person who is in the market for the niche? Why not share it. Many thanks for your time. Come back soon.
This Website
Report this page